自動混凝土攪拌機常見故障有攪拌軸悶車、攪拌時產生異響、減速箱噪音嚴重、減速箱溫度過高、攪拌罐兩端軸溫度過高、軸端漏漿。那么，常見故障的原因是什么呢?下面本文就具體為大家進行介紹。

The common faults of automatic concrete mixer include: the mixing shaft is blocked, abnormal noise is generated during mixing, the noise of reducer is serious, the temperature of reducer is too high, the temperature of shafts at both ends of the mixing tank is too high, and the shaft end leaks slurry. What are the causes of common failures? This article will introduce you in detail.

常見故障一:攪拌軸悶車

Common fault I: the mixer shaft is stuck

1、嚴重超載,這時需要重新調整進料質量,卸出多余物料;

1. In case of serious overloading, it is necessary to readjust the feeding quality and unload the excess materials;

2、自動混凝土攪拌機攪拌葉片或側葉片與罐內壁間有大的異物,這時需要人工排除異物并重新調整間隙;

2. There is a large foreign matter between the mixing blade or side blade of the automatic concrete mixer and the inner wall of the tank. At this time, it is necessary to manually remove the foreign matter and readjust the gap;

3、電機皮帶過松,這時需要調整緊張裝置,拉緊皮帶。

3. The motor belt is too loose. At this time, the tension device needs to be adjusted to tighten the belt.

常見故障二:攪拌時產生異響

Common fault 2: Abnormal noise during mixing

葉片或端刮板與罐內壁間隙過大,這時需要調整間隙到規定要求;

The clearance between the blade or end scraper and the inner wall of the tank is too large, so the clearance needs to be adjusted to the specified requirements;

常見故障三:減速箱噪音嚴重

Common fault 3: the gearbox is noisy

箱內有異物,這時候需要清除異物,修理或將損壞零件換新;

If there is foreign matter in the box, it is necessary to remove the foreign matter, repair or replace the damaged parts;

軸承損壞,這時需要換新的軸承。

The bearing is damaged and needs to be replaced.

常見故障四:減速箱溫度過高

Common fault 4: The gearbox temperature is too high

油的粘度過高或過低,這時需要將油放出,補充新油;

If the viscosity of oil is too high or too low, it is necessary to drain the oil and replenish new oil;

軸承損壞,這時需要換新軸承。

The bearing is damaged and needs to be replaced.

常見故障五:攪拌罐兩端軸溫度過高

Common fault 5: The shaft temperature at both ends of the mixing tank is too high

自動混凝土攪拌機的軸承損壞,這時需要換新的軸承;

The bearing of the automatic concrete mixer is damaged and needs to be replaced;

供油量不足,這時需要按規定要求家注潤滑油。

In case of insufficient oil supply, lubricating oil shall be injected as required.

常見故障六:軸端漏漿

Common fault 6: slurry leakage at shaft end

浮動密封損壞,這時需要換新浮動密封。

The floating seal is damaged and needs to be replaced.

導致自動混凝土攪拌機使用出現6個故障的原因就講解到這里，提前了解到問題就能提前進行處理解決預防，才能保障人身安全以及施工質量，更多相關信息的了解就來我們網站http://www.mwzdpx.com看看吧！

Here are the reasons for six failures in the use of automatic concrete mixer. If you know the problems in advance, you can deal with them, solve them and prevent them in advance, so as to ensure personal safety and construction quality. For more information, please come to our website http://www.mwzdpx.com Look!